> For the complete documentation index, see [llms.txt](https://docs.themeatstick.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.themeatstick.com/your-product/blow/mount-kettle-bullet-drum.md).

# Mounting on a kettle, bullet or drum smoker

On a kettle, a bullet smoker (like the Weber Smokey Mountain) or a drum smoker, the Blow clips into an **existing air opening if your cooker has an accessible one** (on a bullet smoker this can be a bottom vent, with the other vents taped). It depends on the cooker. If there is no accessible opening, the Blow mounts through **one 1¼" (32 mm) hole** in the side of the cooker, as below.

## Fit the spring clip

The spring clip ships separate from the fan. Fit it before you mount the Blow on any cooker:

1. Put the gasket over the Blow's outlet opening.
2. Set the spring clip into the outlet.
3. Screw down through the spring clip.
4. Fit the nut underneath and tighten it firmly.

<figure><img src="https://480337956-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-Mg4Jg9fo_8jMW0As7z7%2Fuploads%2FYD8qpITPS48FY5B7favP%2Fblow-fit-clip.png?alt=media" alt="Fitting the spring clip"><figcaption><p>1: gasket onto the outlet. 2: spring clip into the middle of the opening. 3: screw down through the clip. 4: nut underneath, tightened.</p></figcaption></figure>

## 1. Choose the spot

Pick a spot on the bottom of the cooker where it takes in air:

* **Below the charcoal grate**, so the air goes into the fire.
* **Clear of the ash sweep or damper blades** (move them through their full travel to check).
* **Clear of the legs.** The Blow hangs down below the hole, so it needs open space around and below it, not just a clear hole. A leg right next to the hole will stop it seating.

<figure><img src="https://480337956-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-Mg4Jg9fo_8jMW0As7z7%2Fuploads%2F8YxP7xzwuyVEhWx4w5cl%2Fblow-drill-zone.png?alt=media" alt="Where to drill on a kettle"><figcaption><p>Kettle shown. 1: drill in the shaded zone, on the bowl below the charcoal grate (dashed line) and clear of the legs.</p></figcaption></figure>

## 2. Drill the hole (only if there is no accessible opening)

Drill one **1¼" (32 mm)** hole with a 1¼" hole saw or step bit. The bit sets the size, so you don't need a template. Wear eye protection, and smooth off any sharp edges.

## 3. Mount it

The clip has three legs, so it goes in two-then-one:

1. Hold the Blow up to the hole and seat the **two bottom legs** inside first.
2. **Push the third, top leg in with your thumb.** All three spring open behind the wall and pull the gasket tight against the cooker.
3. Give the Blow a gentle twist so it hangs **body-down, ports facing the ground**, and check it sits firm.

<figure><img src="https://480337956-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-Mg4Jg9fo_8jMW0As7z7%2Fuploads%2FSFHV5xau1o4ZF2MbCZ7p%2Fblow-clip-insert.png?alt=media" alt="Two legs in, then the top one"><figcaption><p>1: the two bottom legs go through first. 2: push the top leg in with your thumb.</p></figcaption></figure>

## 4. Seal the other vents

* **The Blow must control all the air.** Close your cooker's other intakes and seal them (and any leaks) with the high-temp foil tape.
* **Start the top vent at about a pencil-width** (about ⅛ open), then adjust after your first cook.
* **Blow off the cooker?** If you drilled a hole, cover it with the high-temp foil tape from the box.

> If the cooker climbs past your target with every other vent shut, air is getting in somewhere else. Find the leak and tape it: the Blow can't hold temperature against an air leak.

<figure><img src="https://480337956-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-Mg4Jg9fo_8jMW0As7z7%2Fuploads%2FrIDkEUTCYKiVlN4w89wk%2Fblow-vents.png?alt=media" alt="Air in through the Blow, out the top vent"><figcaption><p>1: the other intakes shut. 2: the top vent open a crack. All the air now comes in through the Blow.</p></figcaption></figure>

Next: [Set it up](https://docs.themeatstick.com/your-product/blow/set-up), step 3: connect the probe, the Hub and power
